Technology Care Partner Network · Zurich, Switzerland

Become a Certified Surface Cleanliness Partner

CleanCertify™ is the surface cleanliness track of the Technology Care Partner Network. Cleaning and facility service providers who are trained on our equipment earn a partner credential their clients can verify online, and every job they measure ends in a report analyzed by our Swiss laboratory.

Become a Partner Verify a Partner or Report
Verifiable partner credential Ionic contamination per ISO 8502-9 Live online verification
CleanCertify ionic surface contamination scanner
CleanCertify Scanner · ISO 8502-9
ISO 8502-9
Measurement Method
µg/cm²
Ionic Contamination
Swiss
Laboratory Analysis
QR
Partners & Reports Verified
One Network, Two Tracks

The Surface Cleanliness Track of the Technology Care Partner Network

Technology Care in Zurich runs one partner network with two specialist certification tracks. Partners can qualify for one or both, depending on their training, equipment and the services they offer.

You are here · cleancertify.com

CleanCertify™

For cleaning companies, hygiene providers and contamination-control specialists who verify surface cleanliness with measurement.

  • Data centers, server and comms rooms
  • Telecom sites, control and UPS rooms
  • Electronics manufacturing and cleanrooms
  • Commercial cleaning and facility services
Apply for CleanCertify
Sister track · aircertify.com

AirCertify™

For companies that measure and help improve indoor air quality, airborne particles, gases and corrosive environments.

  • Airborne particles per ISO 14644-1
  • Corrosive gases per ANSI/ISA-71.04
  • VOC, CO₂, formaldehyde and other IAQ values
  • HVAC and building service providers
Visit AirCertify
ISO 8502-9

Ionic Contamination

Soluble salts on surfaces in µg/cm², measured on site with calibrated scanners.

ISO 14644-9

Particle Surface Cleanliness

Particles deposited on floors, raised-floor voids, racks and equipment.

Laboratory analysis

Surface Dust Testing Specialty

Card-sampled dust tested for biological contamination, zinc whiskers, off-gassing and more.

Before & after

Cleaning Verification

Measurements before and after a job document the result of the cleaning.

One partner ID across both tracks. Partners certified for both CleanCertify™ and AirCertify™ keep a single partner ID, and their verification page shows every track and specialty they hold.

The Hidden Risk

Why Ionic Contamination Matters in Data Centers

Dust and residues in technical rooms often carry soluble salts such as chlorides and sulfates. They are invisible after cleaning, yet they are what attacks electronics.

Salts Attract Moisture

Ionic residues absorb moisture from the air and form a conductive film on surfaces, even at humidity levels considered normal for a data center.

Corrosion & Short Circuits

That film drives corrosion of contacts and connectors, leakage currents and electrochemical migration, leading to intermittent faults and hardware failures.

Warranty & Liability

Hardware makers set environmental cleanliness conditions for their equipment. A laboratory cleanliness report documents the condition of the room after cleaning.

Not Ordinary Hygiene Testing

Ionic Testing for Technical Rooms

Ordinary facilities check cleaning with biological tests. Technical rooms also need a test for the contamination that actually damages equipment.

Biological (ATP) Testing

Typical in offices, kitchens, hospitals and food production

  • Detects organic and biological residue
  • Answers “is it hygienic for people?”
  • Does not detect the salts that corrode electronics
How It Works

From Cleaning to Verified Report

The partner cleans and measures, our Swiss laboratory analyzes, and the facility gets a report it can verify. The people doing the cleaning never write the results.

01

Clean & Measure

A certified partner measures floors, raised-floor voids, racks and other surfaces with calibrated Technology Care scanners and samplers. Scanner readings are encrypted at the point of capture.

02

Analyze

The data and samplers go to our laboratory in Zurich, which analyzes them per ISO 8502-9 and the other methods in scope, and issues the report.

Equipment

The Tools Behind the Credential

CleanCertify™ partners work with Technology Care scanners and samplers, analyzed by our Swiss laboratory. Each tool you add opens up a new service you can offer your clients.

DustTrace ionic surface contamination scanner
ISO 8502-9

DustTrace™ Ionic Scanner

Calibrated on-site measurement of ionic surface contamination in µg/cm².

View DustTrace
Serial-numbered card sampler for collecting surface dust
Laboratory analysis

Surface Dust Card Samplers

Free serial-numbered samplers for ionic, biological, zinc whisker and other lab tests.

Ask about samplers
DustLog contamination event logger
ISO 8502-9 · ISO 14644-1

DustLog™ Event Logger

Records chloride-laden dust for months, as evidence before and after events.

View DustLog
CorrLog corrosion logger
ANSI/ISA-71.04 · ISO 8502-9

CorrLog™ Corrosion Logger

Actual corrosion plus the chloride load that drives future corrosion.

View CorrLog
Why Certify

A Credential That Helps You Win Business

Any company can say it cleans well. A verifiable credential sets you apart, and a laboratory report turns your work into proof.

Stand Out in Tenders

Show prospects a partner badge they can verify in seconds, on your website, in proposals and on site.

Results Your Clients Trust

Reports from our Swiss laboratory are more readily accepted by operators, auditors and insurers than a visual inspection by the same company that cleaned.

Higher-Value Contracts

Measured cleaning verification is a premium, repeatable service you can sell on top of your existing cleaning work.

Verification

Verify a Partner or a Report

Partner certificates and job reports both carry a QR code and an ID. Scan the code with your phone camera, or enter the ID below. The live page on cleancertify.com is the authority, not the printed copy.

Verify a Partner

Check that a company is a current CleanCertify™ partner, and see its track and scope.

Please enter the partner ID exactly as shown on the certificate or badge.

The partner ID appears on the partner certificate and next to the CleanCertify™ badge.

Verify a Report

Check that a job report was issued by our laboratory and has not been altered.

Please enter the report number exactly as printed on the report.

The report number is printed next to the QR code on every report.

Partner pages and report copies are published only by Technology Care in Zurich, Switzerland. A credential is valid only if the page address begins with https://cleancertify.com/ or https://aircertify.com/. If a partner shows as expired, a report doesn’t match its online copy, or nothing is found, please contact us at contact@technologycare.com.
Questions

Frequently Asked

CleanCertify™ is the surface cleanliness track of the Technology Care Partner Network, run by Technology Care in Zurich, Switzerland. Technology Care supplies the equipment and training, and its Swiss laboratory analyzes the measurements and issues the reports. More about the equipment is at technologycare.com.

Cleaning and facility service companies, hygiene providers and contamination-control specialists, especially those serving data centers, server and comms rooms, telecom sites, control rooms and other technical facilities. Send us an enquiry and we’ll discuss which specialties fit your services.

The partner certificate shows that a company is trained and authorized to deliver specified measurement services with Technology Care equipment. A report covers one facility on one date: it states what was measured and the results our laboratory found. Both can be verified on this site.

Biological tests show whether a surface is hygienic for people. They don’t detect the soluble salts that cause corrosion and short circuits in electronics, which is the risk that matters in a technical room. CleanCertify™ measures that ionic contamination directly. Where biological results are also needed, dust collected with our card samplers can be tested in our laboratory.

Depending on the job, ionic surface contamination per the ISO 8502-9 conductometric method in µg/cm², particle surface cleanliness per ISO 14644-9, and laboratory results from card-sampled surface dust. Each report lists the methods used and the scope covered, giving an instrument-based result in place of a visual inspection.

No. CleanCertify™ is a partner credential issued by Technology Care. It applies only to the scope stated on the partner’s verification page and does not by itself establish regulatory approval or independent accreditation of the partner or its services.

Scan the QR code on the certificate, badge or report, or enter the partner ID or report number in the Verify section above. The live page on cleancertify.com is the authority; a printed certificate is only valid while the partner’s online status shows as active.

SwissTester™ partners are moving to CleanCertify™ and AirCertify™. Please contact us with your existing partner ID, and we’ll reissue your credential on the track or tracks that match your services.

Yes, through our sister track AirCertify™ at aircertify.com. Partners can hold both tracks under a single partner ID.

For Cleaning & Facility Service Providers

Become a CleanCertify™ Certified Partner

Earn a credential that helps you win business, and give your clients laboratory proof of surface cleanliness. Tell us about your company and the facilities you clean, and our team in Zurich will get in touch.

  • Partner ID & badge — with a live verification page
  • Training & equipment — ionic scanning and surface dust sampling
  • Swiss laboratory reports — every job verifiable by QR code
The partner program is open to businesses only. Please enquire with your company details and work email.

Partner Enquiry

We’ll reply by email to discuss the program with you.

Please enter your name.
Company name is required.
Use your company email — personal addresses (Gmail, Yahoo, etc.) can’t be accepted. Please enter a valid business email address.
Required.

No obligation — we’ll get in touch to discuss the program.